M A T E R I A L ..S A F E T Y ..D A T A ..S H E E T
inkAID™ White Matte Precoat

HAZARD RATINGS NFPA HMIS
Health: 1 1
Flammability: 0 0
Reactivity: 0 0
Personal Protection: ---- B

______________________________________________________________________
Section I General Information

Product Name: InkAID™ White Matte Precoat
Chemical Name: Proprietary Formulation
Chemical Family: Proprietary Formulation
DOT Shipping Hazard: Not Regulated
DOT Hazard Class: None
UN Number: None
Emergency Response: None

______________________________________________________________________
Section II Hazardous Ingredients

CAS Number % TLV/TWA STEL
None

______________________________________________________________________
Section III Physical Data

Freezing Point: 32oF
Specifi c Gravity: 1.08 gm/cc
Percent Solids: 22.5 %
pH: 6.0 +/- 0.5
Appearance: viscous, white liquid.
Weight per Gallon: approx. 9.0
Flash Point: non-fl ammable
Solubility: soluble in

______________________________________________________________________
Section IV Fire and Explosion Hazard Data

Flash Point and Test Method: None - TCC
Flammable Limits: NA
Extinguishing Media: This product is not flammable.
Special Fire Fighting Procedure: None
Unusual Fire and Explosion Hazards: None

______________________________________________________________________
Section V Health Hazard Data

Threshold Limit Value: None established for this product
Effects of Overexposure: Ingestion: May cause gastric disturbance if swallowed.
Inhalation: Mild respiratory irritant.
Skin Exposure: Wash affected area with soap and
water. Remove contaminated clothing and shoes.
Eye Irritation: Rinse immediately with plenty of water.

______________________________________________________________________
Section VI Reactivity Data

Stability: Stable
Conditions to Avoid: None
Incompatibility (materials to avoid): Strong acids, strong alkalis
Hazardous Polymerization: Will not occur
Hazardous Decomposition Products: Oxides of Carbon and Nitrogen

______________________________________________________________________
Section VII Spill or Leak Procedures

Spill Response: Caution - Spilled material can cause slippery surfaces. Ventilate
area. Wear protective equipment.
Small Spills: Wipe, mop, or wash with soap and water, or absorb. Where
permitted, flush with water to a secondary wastewater treatment
system.
Large Spills: Contain and collect for recovery and use or disposal.
Waste Disposal Method: Landfill/incinerate in accordance with applicable local, state,
and federal regulations.

______________________________________________________________________
Section VIII Special Protection Information

Eye Protection: Safety glasses and/or face shield as handling conditions require.
Skin Protection: Liquid proof gloves such as PVC. Plastic or rubber apron, if needed.
Rubber boots for a large spill response.
Respiratory Protection: Not normally needed when ventilation is adequate.
Ventilation Recommended: Normal workplace ventilation. No special ventilation is required.
Other Protective Equipment: Eyewash fountain, safety shower should be in or near work area.

______________________________________________________________________
Section IX Regulatory Information

WHMIS Classification: Not Regulated
All ingredients of this product are listed or are excluded from listing on the U.S. Toxic
Substances Control Act (TSCA) Chemical Substance Inventory.
This product is not subject to the reporting requirements under California’s Proposition 65.
These ingredients from Section II are subject to the following reporting requirements:
PA - The Pennsylvania Hazardous Substance List
NJ - The New Jersey Right to Know Hazardous Substance List
MA - The Massachusetts Hazardous Substance List

______________________________________________________________________
Section X Special Precautions

Precautions in Handling and Storage:

FOLLOW SAFE AND HYGENIC INDUSTRIAL CHEMICAL HANDLING PRACTICES.
USE ONLY IN ACCORDANCE WITH GOOD PRACTICES OF PERSONAL CLEANLINESS
AND HYGIENE. HANDLE WITH DUE CARE AND AVOID UNNECESSARY CONTACT WITH
THIS PRODUCT. AS WITH ALL CHEMICALS, AVOID LIQUID CONTACT WITH EYES, SKIN,
AND CLOTHING. AVOID EXCESSIVE VAPOR EXPOSURES BY INHALATION OR CONTACT.
USE WITH ADEQUATE VENTILATION. STORE IN HEATED BUILDINGS OR HEAT-T
RACED TANKS TO PREVENT FREEZING

THIS INFORMATION IS BEING SUPPLIED TO YOU UNDER OSHA “RIGHT TO KNOW” REGULATION
29 CFR 1910.1200 AND IS OFFERED IN GOOD FAITH AS TYPICAL VALUES AND NOT AS
A PRODUCT SPECIFICATION. THE INFORMATION CONTAINED HEREIN IS BASED ON DATA
AVAILABLE TO US AND IS BELIEVED TO BE TRUE AND ACCURATE.
NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY OF THIS DATA, THE
HAZARDS CONNECTED WITH THE USE OF THE MATERIAL, OR THE RESULTS TO BE
OBTAINED FROM THE USE THEREOF, IS MADE. ONTARIO SPECIALTY COATINGS CORPORATION
ASSUMES NO RESPONSIBILITY FOR DAMAGE OR INJURY FROM THE USE OF THE
PRODUCT DESCRIBED HEREIN.
Manufactured by
ONTARIO SPECIALTY COATINGS CORPORATION
16830 County Route 155 Watertown, New York, U.S.A. 13601