home..products..instructions..FAQ .orders..portfolio..links..store.

 

Gallerie Wrap




            • First you need to start
          with your printed image  


            • For the standard Gallerie
          Wrap your image needs to
          be 3" larger than the frame
          size                  

 
            • For PRO Wraps your image
          needs to be 4" larger than
          the frame size
 
Step One:
 
 
     • Peel the yellow cover to expose
     adhesive on the bars

 
     • Insert the bars into the
     positioning corner with the
     adhesive facing up


     • Make sure the bars are flush
     with the positioning corner      edge, and pressed firmly down
     inside the corner


     • The positioning corners have
     tabs so that the bars may only
     be inserted properly

     

 
 
       
  Time for step 1: 1 minute Accumulative Time: 1 minute
       
 
Step Two:
   


            • Flip the frame over and center
          the frame over art work in
          the desired position


            • Firmly push bars down so they
          make contact with the back
          of the media
   
Time for step 2: 20 seconds Accumulative Time: 1 minute, 20 seconds
   
 
Step Three:
   


            • Remove the positioning
          corners by pulling up while
          holding the stretcher bars
          down
   
Time for step 3: 15 seconds Accumulative Time: 1 minute, 35 seconds
   
 
Step Four:
   
 
            • You will need a sharp utility
          knife for this step
 

            • Trim the excess material
          around the edges of the
          stretcher bars
   
Time for step 4: 1 minute, 30 seconds Accumulative Time: 3 minutes, 5 seconds
   
 
Step Five:
   


            • Run a small bead of pH
          neutral glue along the inside
          of the stretcher bars
   
Time for step 5: 30 seconds Accumulative Time: 3 minutes, 35 seconds
   
 
Step Six:
   



             • Cut the corners outward
           where the bars meet at a
           45 degree angle
   
Time for step 6: 10 seconds Accumulative Time: 3 minutes, 45 seconds
   
 
Step Seven:
   



            • Fold the corners onto the
          beveled ends (on adhesive)
   
Time for step 7: 15 seconds Accumulative Time: 4 minutes
   
 
Step Eight:
   


            • Pull the bars up close to the
          frame
  
 
            • Insert the staple into the slot

            • Push or gently hammer staple
          flush into the frame
 

            • Repeat on remaining corners
   
Time for step 8: 30 seconds Accumulative Time: 4 minutes, 30 seconds
   
 
Step Nine:
   


            • Insert fout tensioners into the
          v-slots located in the frame           corners
 

            • Make sure tensioners are not
          touching artwork
 

            • Insert center brace if needed
          (Pro Gallerie Wrap only)
   
Time for step 9: 15 seconds Accumulative Time: 4 minutes, 45 seconds
   
 
Wrap Completed
   



            • Flip over the piece  

            • Here is your finished                    Hahnemuhle Gallerie Wrap  



              Congratulations!
   
In Just Five Minutes
   
 

For questions regarding application suitability or usage, or to receive inkAID news contact support.

Disclaimer of Warranty
Due to the wide variety of substrates, equipment, and conditions under which these products may be used, they are sold without any warrenty, express or implied, as to performance or merchantability. The suitability of any product for an intended purpose shall be solely determined by the user.

No inkAID representative has the authority to wave or change these provisions, which apply to all sales. Any liability of seller, agent, parent company, other affiliates, or manufacturer will be limited exclusively to product replacement or refund of the purchase price.

All images and content Copyright © 2008.