MSDS- inkAID™ Adhesive
M A T E R I A L ..S A F E T Y ..D A T A ..S H E E T
inkAID™ Adhesive
HAZARD RATINGS NFPA HMIS
Health: 1
Flammability: 0
Reactivity: 0
Personal Protection: —- B
______________________________________________________________________
Section I General Information
Product Name: inkAID™ Adhesive (for Clear Gloss Precoat)
Chemical Name: Proprietary Formulation
Chemical Family: Proprietary Formulation
DOT Shipping Hazard: Not Regulated
DOT Hazard Class: None
UN Number: None
Emergency Response: None
______________________________________________________________________
Section II Ingredients
OSHA OSHA
CAS Number % TLV/TWA STEL
Water 7732-18-5 45 – 50 NOT ESTABLISHED
Acrylic Polymers 45 – 50 NOT ESTABLISHED
(Non- Hazardous)
Ammonium 1336-21-6 2 – 4 NOT ESTABLISHED
Hydroxide, 28%
The ammonium hydroxide listed above forms a salt of the polymer, which solubilizes
the polymer in water. The amount of free ammonia that may be present is below the de
minimus levels for disclosure. Toxicology studies of products containing similar levels
of polymer salt indicate that the products may be classified as non-hazardous.
______________________________________________________________________
Section III Physical Data
Freezing Point: 32ºF
Specific Gravity: 1.03 gm/cc
Percent Solids: 43.2 %
pH: 7.5 +/- 0.5
Appearance: Clear to tan liquid.
Weight per Gallon: approx. 8.59
Flash Point: non-flammable
Solubility: soluble in water
______________________________________________________________________
Section IV Fire and Explosion Hazard Data
Flash Point and Test Method: None – TCC
Flammable Limits: NA
Extinguishing Media: Foam. CO2. Dry Chemical. Water Fog
Special Fire Fighting Procedure: None
Unusual Fire and Explosion Hazards: None
______________________________________________________________________
Section V Health Hazard Data
Threshold Limit Value: None established for this product
Carcinogens Under OSHA, None Known
ACGIH, NTP, IARC
Effects of Overexposure: Ingestion: May cause gastric disturbance if swallowed.
Inhalation: Mild respiratory irritant.
Skin Exposure: May cause mild skin irritation.
Eye Irritation: May cause mild eye irritation.
First Aid Measures: Ingestion: Immediately drink 1 –2 glasses of water or milk. If
discomfort persists, seek medical attention. Do not administer
anything by mouth to an unconscious person.
Inhalation: Remove to fresh air. If breathing is affected, get
medical attention.
Skin Contact: Wash contaminated area with water and soap. If
irritation develops, get medical attention.
Eye Contact: Rinse with plenty of water. If irritation develops, get
medical attention.
______________________________________________________________________
Section VI Reactivity Data
Stability: Stable
Conditions to Avoid: None
Incompatibility (materials to avoid): None Known
Hazardous Polymerization: Will not occur.
Hazardous Decomposition Products: Oxides of Carbon and Nitrogen
______________________________________________________________________
Section VII Spill or Leak Procedures
Spill Response: Caution – Spilled material can cause slippery surfaces. Ventilate area.
Wear protective equipment. Product contains ammonia. May be toxic
to aquatic life. Do not let spilled or leaking material enter watercourse.
Small Spills: Absorb with oil-dry or similar inert material. Sweep or scrape up and
containerize. Rinse affected area thoroughly with water.
Large Spills: Contain and collect for recovery and use or disposal.
Waste Disposal
Method: Dispose in accordance with applicable local, state, and federal regulations
regarding disposal of non-hazardous material.
______________________________________________________________________
Section VIII Special Protection Information
Eye Protection: Safety glasses and/or face shield as handling conditions require.
Skin Protection: Liquid proof gloves such as PVC. Plastic or rubber
apron, if needed. Rubber boots for a large spill response.
Respiratory Protection: Not normally needed when ventilation is adequate.
Ventilation Recommended: Normal workplace ventilation. No special ventilation is
required.
Other Protective Equipment: Eyewash fountain, safety shower should be in or near work
area.
______________________________________________________________________
Section IX Regulatory Information
WHMIS Classification: Not Regulated
All ingredients of this product are listed or are excluded from listing on the U.S. Toxic
Substances Control Act (TSCA) Chemical Substance Inventory.
This product is not subject to the reporting requirements under California’s Proposition 65.
These ingredients from Section II are subject to the following reporting requirements:
PA – The Pennsylvania Hazardous Substance List
NJ – The New Jersey Right to Know Hazardous Substance List
MA – The Massachusetts Hazardous Substance List
______________________________________________________________________
Section X Special Precautions
USE ONLY IN ACCORDANCE WITH GOOD PRACTICES OF PERSONAL CLEANLINESS AND
HYGIENE. HANDLE WITH DUE CARE AND AVOID UNNECESSARY CONTACT WITH THIS PRODUCT.
AS WITH ALL CHEMICALS, AVOID LIQUID CONTACT WITH EYES, SKIN, AND CLOTHING.
AVOID EXCESSIVE VAPOR EXPOSURES BY INHALATION OR CONTACT. USE WITH ADEQUATE
VENTILATION.
THIS INFORMATION IS BEING SUPPLIED TO YOU UNDER OSHA “RIGHT TO KNOW” REGULATION
29 CFR 1910.1200 AND IS OFFERED IN GOOD FAITH AS TYPICAL VALUES AND NOT AS
A PRODUCT SPECIFICATION. THE INFORMATION CONTAINED HEREIN IS BASED ON DATA
AVAILABLE TO US AND IS BELIEVED TO BE TRUE AND ACCURATE.
NO WARRANTY, EXPRESSED OR IMPLIED, REGARDING THE ACCURACY OF THIS DATA, THE
HAZARDS CONNECTED WITH THE USE OF THE MATERIAL, OR THE RESULTS TO BE
OBTAINED FROM THE USE THEREOF, IS MADE. ONTARIO SPECIALTY COATINGS CORPORATION
ASSUMES NO RESPONSIBILITY FOR DAMAGE OR INJURY FROM THE USE OF THE
PRODUCT DESCRIBED HEREIN.
Manufactured by
ONTARIO SPECIALTY COATINGS CORPORATION
22564 Fisher Road Watertown, New York, U.S.A. 13601
